WAVE® MUSIC SYSTEM
MULTI-CD CHANGER
Owner’s Guide | Guía de usuario | Notice d’utilisation
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
Please read this owner’s guide
CAUTION: To prevent electric shock, match the wide
blade of the line cord plug to the wide slot of the AC
(mains) receptacle. Insert fully.
Please take the time to follow the instructions in this
owner’s guide carefully. It will help you set up and
operate your system properly and enjoy its advanced
features. Please save this owner’s guide for future
reference.
CAUTION: Use of controls or adjustments or performance
of procedures other than those specified herein may result
in hazardous radiation exposure from the internal laser
component. The compact disc player should not be
adjusted or repaired by anyone except properly qualified
service personnel.
WARNING: To reduce the risk of fire or electrical shock,
do not expose the product to rain or moisture.
WARNING: Do not expose this
apparatus to dripping or splashing,
CAUTION: Make no modifications to the system or acces-
sories. Unauthorized alterations may compromise safety,
regulatory compliance and system performance.
and do not place objects filled with
liquids, such as vases, on or near the
apparatus. As with any electronic products, use care not to
spill liquids into any part of the system. Liquids can cause a
failure and/or a fire hazard.
Note: The product label is located on the bottom of the
product.
WARNING: Do not place any naked flame sources, such
as lighted candles, on or near the apparatus.
Note: The product must be used indoors. It is neither
designed nor tested for use outdoors, in recreational
vehicles, or on boats.
CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
Note: Where the mains plug or appliance coupler is used
as the disconnect device, such disconnect device shall
remain readily operable.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL.
Note: This product is intended to be used only with the
The lightning flash with arrowhead symbol within an
equilateral triangle alerts the user to the presence of
uninsulated dangerous voltage within the system
enclosure that may be of sufficient magnitude to
constitute a risk of electrical shock.
Bose® Wave® music system.
This product conforms to all applicable
EU Directive requirements. The complete
Declaration of Conformity can be found at
The exclamation point within an equilateral triangle,
as marked on the system, is intended to alert the
user to the presence of important operating and
maintenance instructions in this owner’s guide.
Class 1 laser product
This CD player is classified as a CLASS 1 LASER
PRODUCT according to EN/IEC 60825.
CLASS 1
KLASSE 1
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LUOKAN
KLASS
1
1
LASER APPARAT
2 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions – for all components
10. Protect the power cord from being walked on
or pinched, particularly at plugs, convenience
receptacles, and the point where they exit
from the apparatus.
before using this product.
2. Keep these instructions – for future reference.
3. Heed all warnings – on the product and in the
11. Only use attachments/accessories specified
by the manufacturer.
owner’s guide.
4. Follow all instructions.
12. Use only with the cart, stand,
tripod, bracket or table specified by
the manufacturer or sold with the
apparatus. When a cart is used, use
caution when moving the cart/
apparatus combination to avoid injury from
tip-over.
5. Do not use this apparatus near water or
moisture – Do not use this product near a bathtub,
washbowl, kitchen sink, laundry tub, in a wet
basement, near a swimming pool, or anywhere else
that water or moisture are present.
6. Clean only with a dry cloth – and as directed by
Bose Corporation. Unplug this product from the wall
outlet before cleaning.
13. Unplug this apparatus during lightning storms
or when unused for long periods of time – to
prevent damage to this product.
7. Do not block any ventilation openings. Install
in accordance with the manufacturer’s
instructions – To ensure reliable operation of the
product and to protect it from overheating, put the
product in a position and location that will not
interfere with its proper ventilation. For example,
do not place the product on a bed, sofa, or similar
surface that may block the ventilation openings.
Do not put it in a built-in system, such as a
14. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way: such
as power-supply cord or plug is damaged;
liquid has been spilled or objects have fallen
into the apparatus; the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped – Do not attempt
to service this product yourself. Opening or
bookcase or a cabinet that may keep air from
flowing through its ventilation openings.
removing covers may expose you to dangerous
voltages or other hazards. Please call Bose to be
referred to an authorized service center near you.
8. Do not install near any heat sources, such
as radiators, heat registers, stoves or other
apparatus (including amplifiers) that produce
heat.
15. To prevent risk of fire or electric shock, avoid
overloading wall outlets, extension cords, or
integral convenience receptacles.
9. Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding-type plug has two blades
and a third grounding prong. The wider blade
or third prong are provided for your safety. If
the provided plug does not fit in your outlet,
consult an electrician for replacement of the
obsolete outlet.
16. Do not let objects or liquids enter the
product – as they may touch dangerous voltage
points or short-out parts that could result in a fire
or electric shock.
17. Use Proper Power Sources – Plug the product
into a proper power source, as described in the
operating instructions or as marked on the product.
English – 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Information about products that generate
electrical noise
For your records
Record the serial number of your new multi-disc changer
in the space below. The serial number can be found on
the bottom panel.
If applicable, this equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, this
is no guarantee that interference will not occur in a
particular installation.
Serial number ___________________________________
Purchase date __________________________________
We suggest you keep your receipt with this owner’s
guide.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, you are
encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment to an outlet on a different
circuit than the one to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Note: Unauthorized modification of the receiver or radio
remote control could void the user’s authority to operate
this equipment.
This product complies with the Canadian ICES-003
Class B specifications.
Note to CATV system installer
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC (of USA)
that provides guidelines for proper grounding. In
particular, it specifies that the cable ground shall be
connected to the grounding system of the building,
as close to the point of cable entry as is practical.
©1994-2012 Bose Corporation. No part of this work may be reproduced, modified, distributed or otherwise used without prior
written permission. All trademarks referenced herein are property of Bose Corporation. The Wave® music system design is a
registered trademark of Bose Corporation.
4 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
SETUP .................................................. 6
Introduction ........................................................... 6
Unpacking the carton ............................................ 6
Selecting a location for your system ..................... 6
Seating your Wave® music system on
the Multi-CD Changer ........................................... 6
Connecting the Multi-CD Changer to your
Wave® music system ............................................. 7
OPERATION ........................................... 8
Remote control guide ............................................ 8
Turning your multi-CD system on and off ............. 9
Loading and unloading discs ................................ 9
Loading CDs into the Wave® music
system (Disc 1) ................................................... 9
Loading CDs into the Multi-CD
Changer (Disc 2 - Disc 4) ................................... 9
Unloading discs .................................................. 9
Playing CDs ........................................................... 10
Moving to another CD ........................................ 10
Stopping a CD .................................................... 10
Ejecting a CD ..................................................... 10
Changing Play Modes ........................................ 10
Connecting an external audio source .................... 11
Playing a connected audio source ........................ 11
CARE AND MAINTENANCE ........................ 12
Cleaning ................................................................. 12
Troubleshooting ..................................................... 12
Customer Support ................................................. 12
Limited warranty .................................................... 12
Technical information ............................................ 13
CONTACT INFORMATION .......................... 14
English – 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP
Introduction
Selecting a location for
your system
Thank you for purchasing the Bose® Wave® music
system Multi-CD Changer accessory.
Adding the Multi-CD Changer to your Wave® music
system provides you with some valuable benefits:
• A four-disc Wave® music system – Allows you to
load and play up to four audio CDs. Provides hours
of uninterrupted CD music.
Your Multi-CD Changer is designed to fit directly under
your Wave® music system. Before you connect the
Multi-CD Changer to the Wave® music system, select a
good location for the complete system using the follow-
ing guidelines.
• Place the system on a table or other flat surface.
• To enjoy maximum performance, place the system
across the room from where you will be listening.
• Elegant integrated pedestal design – Using the
same footprint as the Wave® music system, the
changer complements the elegance and simplicity
of the system.
• Place the system within two feet of a wall, and avoid
placing it directly in a corner.
• One integrated remote control – Provides the
simplicity of using the remote control that came with
your Wave® music system and one-touch selection of
all built-in sources.
CAUTION: DO NOT place your system on a heat-sensitive
surface. Like all electrical equipment, it generates some
heat.
• Multiple source switching – By adding two input
connections for external audio devices, you can enjoy
listening to one or two other audio sources in your
home through the Wave® music system.
CAUTION: DO NOT use your system in a damp location
or any other place where moisture can get inside.
Note: DO NOT place your system on a metal surface.
It could interfere with AM reception.
Unpacking the carton
Carefully unpack your Wave® music system Multi-CD
Changer and save all packing materials for possible
future use. The original packing materials provide the
safest way to transport your new Multi-CD Changer.
Seating your Wave® music
system on the Multi-CD
Changer
Make sure you received the parts shown in the following
diagram. If any part appears damaged, do not attempt
to use it. Notify Bose customer service immediately
(see phone numbers on the inside back cover).
With the changer placed in your chosen location, care-
fully set your Wave® music system on top of the changer.
• Make sure the rear feet of the Wave® music system fit
into the recesses on top of the changer.
• Make sure the Wave® music system sits flat and the
side edges of both units are aligned.
Wave® music system Multi-CD Changer
6 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP
3. Plug the AC power cord from the Wave® music
system into the AC power input connector on
the back of the changer.
Connecting the Multi-CD
Changer to your Wave®
music system
4. Plug the other end of the AC power cord into an AC
(mains) wall outlet.
Before you start this setup procedure, disconnect
the AC power cord on your Wave® music system
and set it aside. You will need to use it again in
Step 3.
After applying power, “PLEASE WAIT” appears
on the display for about 30 seconds while the
system prepares itself for operation. DO NOT
insert any discs until this message disappears.
1. Plug the Bose® link cable from the changer into the
5. For best FM reception, straighten the AC power cord
as much as possible. Your Wave® music system uses
the power cord as an FM antenna.
Bose® link connector on your Wave® music system.
2. Plug the changer power cord into the AC power input
connector on the back of the Wave® music system.
AC
POWER
input
Wave® music
system
4
Wave® music system
AC power cord
Multi-CD
Changer
2
1
Changer
power
cord
3
Bose® link connector
Bose® link cable
AC POWER input
For best FM reception,
straighten the power
cord as much as
possible.
5
English – 7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Remote control guide
Note: Press-and-hold operations require holding the
button down for at least one second.
Your Wave® music system remote will operate the
Multi-CD Changer. Just aim the remote at the front panel
and press the buttons. The remote normally works within
20 feet of the front panel.
Note: Pressing RADIO, CD, or AUX automatically turns
on the Wave® music system to the source selected.
The following diagram describes the buttons used for
playing CDs using the disc changer.
CD
• Press: Selects the CD source (page 10).
• Press again: Moves to the next disc
(page 10).
AUX
Seek/Track
• Press to hear audio from an external
source connected to either the AUX 1 or
AUX 2 input on the changer (page 11).
• Press: Skips to next/previous CD track
on the current disc.
• Press and hold: Rapidly skips to next/
previous CD track on the current disc.
• Press to switch between the AUX 1 and
AUX 2 input (page 11).
Tune/MP3
Stop/Eject
• Press: Navigates between folders
when playing MP3 CDs.
• Press once: Stops playing the current CD
(page 10).
• Press and hold: Rapidly scans forward/
backward through a CD track.
• Press again: Ejects the stopped CD.
• Press and hold: Ejects a playing CD.
Play Mode
Play/Pause
• Selects CD play modes (page 10).
• Press: Plays the current CD.
• Press again: Pauses a playing CD.
8 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Loading CDs into the Multi-CD
Turning your multi-CD
system on and off
Changer (Disc 2 - Disc 4)
Insert a disc, label side up, into an empty slot. An empty
slot is indicated by an unlit disc slot indicator. With your
fingers on the outside edge of the disc, push the disc all
the way into the slot.
Press Power once to turn your multi-CD
Wave® music system on or off. The system
turns on to the last source played. If the last
source was CD, the last disc selected starts to play.
Press Power again to turn the system off.
Press CD to turn the system on to the CD
source. The last disc selected will play.
Loading and unloading
discs
Disc slot indicators
Off .......................... Empty disc slot.
Solid green............. The current disc slot.
Solid amber............ The disc slot contains a
CD, but it is not currently
selected.
You can load and unload discs with the system on or off.
If the system is off or in the CD source mode, the first
disc loaded starts playing automatically. Disc slots are
numbered 1 through 4. The Wave® music system has
disc slot 1. The changer has disc slots 2, 3 and 4.
Loading CDs into the Wave® music
system (Disc 1)
Insert the disc, label side up, into the CD slot below the
display. The disc player will automatically pull the disc in.
Unloading discs
You can unload discs while the system is off
or in the CD source mode. Press Stop/Eject
on the remote control to eject the current
disc. After removing the disc from its slot, the
system moves to the next available disc which then can
be ejected by pressing Stop/Eject again.
For more information on using the Stop/Eject key,
see “Ejecting a CD” on page 10.
CAUTION:
• DO NOT INSERT mini CDs or non-circular CDs into
any disc slot. These discs may not play properly and
could interfere with the system’s ability to eject them.
• DO NOT INSERT more than one disc at a time into any
disc slot.
• Doing either of the above can cause damage to the
disc and/or the disc slot.
English – 9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Changing Play Modes
Playing CDs
While the Multi-CD changer is connected, the following
play modes are available. The system plays continuously
in all modes except SHUFFLE DISC for audio and MP3
CDs, and SHUFFLE FLDR for MP3 CDs only.
With the Multi-CD Changer installed, your Wave® music
system operates as a four-disc changer. Now, when you
play CDs, all the normal CD information appears on the
display with one addition – the selected CD slot number
(d1, d2, d3, or d4) appears in the center of the display.
While playing a CD, press Play Mode repeatedly
until the play mode you want is displayed.
Selected
source
Number of selected CD slot:
d1 = Wave® music system
d2, d3, d4 = changer
Play modes for audio CDs:
• NORMAL PLAY plays all CDs in order.
Play mode
• SHUFFLE plays all tracks on the selected CD in
random order, then moves to the next CD, again
playing all tracks in random order.
• SHUFFLE DISC plays all tracks on the selected CD
once in random order.
• SHUFF RPT CD repeats all tracks on the selected CD
in random order.
Disc
number
Track
number
Elapsed
track time
• REPEAT DISC repeats all tracks on the selected CD
in order.
Note: When switching from the FM, AM, or AUX source
to the CD source, the CD in the most recently used slot
begins playing automatically. If that slot is empty, the next
slot containing a CD is selected.
• REPEAT TRACK repeats the selected track on the
selected CD.
Play modes for MP3 CDs:
The following information describes functions related
to the Multi-CD Changer. Refer to your Wave music
system owner’s guide for complete instructions on
playing the selected CD.
• NORMAL PLAY plays all CDs in order.
• SHUFFLE plays all tracks on the selected CD in
random order, then moves to the next CD, again
playing all tracks in random order.
• SHUFFLE DISC plays all tracks on the selected CD
Moving to another CD
Press CD to move to the next CD slot. The CD
number on the display tells you which CD slot is
currently selected.
once in random order.
• SHUFF RPT CD repeats all tracks on the selected CD
in random order.
• REPEAT DISC repeats all tracks on the selected CD
in order.
Stopping a CD
• SHUFFLE FLDR plays all tracks in the selected folder
once in random order.
Press Stop/Eject once to stop a playing CD.
• SHUF RPT FDR repeats all tracks in a folder in
random order.
Ejecting a CD
• REPEAT FOLDR repeats all tracks in a folder in order.
Press CD on the remote to move to the CD
you want to eject. Press Stop/Eject once to
stop a playing CD and then, press again to
eject the CD.
• REPEAT TRACK repeats the selected track on the
selected CD.
Note: When operating the Wave® music system without
the Multi-CD changer, you can select a music source in the
setup menu to automatically play after a CD ends.
Because the system plays continuously while the Multi-CD
changer is connected, this option is not available.
For more information on ejecting CDs, see “Unloading
discs” on page 9.
10 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Connecting an external
audio source
Playing a connected audio
source
With the Multi-CD changer connected, any external
audio devices you may have used with your Wave®
music system can be connected to the back of the
Multi-CD changer. However, you now need a dual RCA
stereo cable.
The Wave® music system Multi-CD Changer provides
two rear panel inputs (AUX 1 and AUX 2) for external
audio devices such as TV, VCR, DVD player, cassette
player, or MP3 player. This gives you the advantage of
hearing Wave® music system sound from a range of
sources.
To listen to a connected source:
1. Turn on the external device.
2. Press AUX on the Wave® music system
remote control. Press AUX again to switch
between the AUX 1 and AUX 2 inputs. AUX 1
or AUX 2 appears on the display to confirm your
selection.
3. Adjust the volume using the Wave® music system
remote control.
Note: The Wave® music system remote control cannot
turn a connected AUX device on or off, or change its set-
tings or selections.
To connect a device, connect one end of the cable to the
audio output jacks of the source and the other end to
one of the AUX inputs on the changer. Be sure to match
the red and white plugs on the cable to the red (R) and
white (L) AUX jacks on the changer.
Note: Neither AUX 1 or AUX 2 can be selected as an
alarm source.
Connection example:
TV
Red
Red
Dual RCA stereo cable
Use only a stereo connection. You will not hear
the connected device if just the left (L) or right (R)
channel is connected.
English – 11
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
Cleaning
Customer Support
Use only a soft dry cloth to clean your Wave® music
multi-CD system. If necessary, you may use a soft-
bristled attachment to gently vacuum across the front.
Do not use any liquid cleaning solutions, solvents,
chemicals, alcohol, ammonia, or abrasives.
For additional help in solving problems, contact Bose®
Customer Support. Refer to the address list on the
inside back cover of this guide.
Limited warranty
CAUTION: Do not allow liquids to spill into any openings
in the enclosure. If liquids get into the unit, turn it off imme-
diately. Call Bose® Customer Support as soon as possible
to arrange for service. See the list of phone numbers inside
the back cover.
Who is covered:
This warranty is extended only to the original end-use
purchaser or the person receiving the product as a gift,
and shall not be extended to any other person or
transferee.
What is covered/For how long:
Troubleshooting
For a period of 1 year (2 years, European Union) from the
date of retail purchase by the original end-use purchaser,
Bose® warrants that this product, when delivered to you
in new condition, in original packaging, from a Bose
authorized reseller and used in normal conditions, is
free from any defects in manufacturing, materials and
workmanship.
Problem
What to do
The Wave music
system is on but
the changer does
not operate.
• Check the power connections between
the Wave® music system and the
changer (page 7).
What is not covered:
• Make sure the Wave® Multi-CD Changer
is plugged into a live power outlet and
is turned on.
No sound or
sound is muffled
This warranty does not cover defects resulting from
improper or unreasonable use or maintenance; failure to
follow operating instructions; accident; excess moisture;
insects; lightning; power surges; connections to
improper voltage supply; unauthorized alteration or
modification of original condition; damages caused by
inadequate packing or shipping procedures; loss of,
damage to or corruption of stored data; damages
caused by use with non-Bose products; product that
requires modification or adaptation to enable it to
operate in any country other than the country for which
it was designed, manufactured, approved and/or
authorized, or repair of products damaged by these
modifications; and products purchased from
• Check the connections between the
Wave® music system and the changer
(page 7).
• If the AUX source is selected, check the
connections from the AUX source to the
changer and make sure the AUX device
is turned on.
• Disconnect headphones.
No sound heard
from the AUX
device
• Make sure the RCA plugs on the stereo
cable are pushed in as far as they can
go.
• Press AUX on the remote and select
the AUX input used by the device (AUX
1 or AUX 2).
unauthorized dealers.
• Make sure the AUX device is turned on.
What we will do:
During the warranty period, we will, at our sole option,
repair or replace (using new or refurbished replacement
parts) any defective parts within a reasonable period of
time and free of charge.
CD skips
• Make sure the system is not getting
bumped in its current location. If so,
move it to a more protected location.
• Check the CD for smudges or dirt. If
cleaning is necessary, wipe the CD
straight out from the center (NOT in a
circular motion) to clean it.
What we will not do:
Pay shipping, insurance or transportation charges from
you to us, or any import fees, duties and taxes.
CD does not play • Make sure there is a CD in the selected
CD slot.
• Make sure CD is selected on the dis-
play of the Wave® music system .
• Check to see if the CD slot in the Wave®
music system III is selected, instead of
a slot in the Multi-CD Changer.
A CD is playing,
but none of the
Multi-CD Changer
LEDs are lit
12 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
What you must do to obtain
Limited Warranty Service:
Technical information
Return product, with proof of purchase from an
authorized Bose® dealer, using the following procedures:
Multi-CD Changer power rating
120V~ 50/60 Hz, 80W
1. Contact the Boseorganization in your country/region
(visit Global.Bose.com for Bose contact information
in your country/region) for specific return and ship-
ping instructions;
Dimensions
2.6"H x 14.5"W x 9.9"D
(6.6 cm x 36.8 cm x 25.2 cm)
Weight
4.5 lb (2.04 kg)
2. Label and ship the product, freight prepaid, to the
address provided by the Bose organization in your
country; and
Color
3. Place any necessary return authorization number
prominently on the outside of the carton. Cartons
not bearing a return authorization number, where
required, will be refused.
Graphite Gray or Platinum White
Other conditions:
THE PROVISIONS OF THIS LIMITED WARRANTY ARE
IN LIEU OF ANY OTHER WARRANTY, WHETHER
EXPRESSED OR IMPLIED, WRITTEN OR ORAL,
INCLUDING ANY WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. BOSE
CORPORATION'S MAXIMUM LIABILITY SHALL NOT
EXCEED THE ACTUAL PURCHASE PRICE PAID BY
YOU FOR THE PRODUCT. IN NO EVENT SHALL BOSE
BE LIABLE FOR LOSS OF, DAMAGE TO OR
CORRUPTION OF STORED DATA, OR FOR SPECIAL,
INCIDENTAL, CONSEQUENTIAL, OR INDIRECT
DAMAGES HOWSOEVER CAUSED INCLUDING
WITHOUT LIMITATION THE REPLACEMENT OF
EQUIPMENT AND PROPERTY, AND ANY COSTS OF
RECOVERING, PROGRAMMING OR REPRODUCING
ANY PROGRAM OR DATA STORED IN OR USED WITH
YOUR BOSE PRODUCT. THIS WARRANTY IS VOID IF
THE LABEL BEARING THE SERIAL NUMBER HAS
BEEN REMOVED OR DEFACED.
Other legal rights:
This limited warranty gives you specific legal rights, and
you also may have other rights that vary from state to
state or country to country. Some places do not allow
limitations on implied warranties or the exclusion or
limitation of incidental or consequential damages, so the
above limitations or exclusions may not apply to you.
English – 13
Download from Www.Somanuals.com. All Manuals Search And Download.
2012 Bose Corporation, The Mountain,
Framingham, MA 01701-9168 USA
AM352348 Rev 00
Download from Www.Somanuals.com. All Manuals Search And Download.
|